Gate Repair in Antioch, CA | Gate Repair Antioch

Gate Repair in Antioch - On-Site in 60 Minutes, Fixed the Same Day

Most gate faults are diagnosed and fixed on the first visit. You get the price before we start, and the gate is left working and safe before we leave.

We answer 24/7

Work is performed by our local vetted partner.

Free
Written Quotes
Licensed & Insured Written Quotes Free Estimates All Brands Satisfaction Guarantee

Work is performed by our local vetted partner.

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Trusted Gate Repair for Antioch Homeowners

When a driveway gate stops opening, drags on its track, or swings half-closed and gives up, the whole routine of the property changes with it. We handle gate repair in Antioch for homeowners, HOAs and property managers who need the gate working again without rebuilding the entire system. Our technicians have up to 11 years of experience and work on the brand you already have – LiftMaster, FAAC, BFT and more – so a failed operator usually doesn’t mean a new gate. Same-day service is available when you call before dispatch fills, and we can often return the same visit once we see the equipment.

Call (855) 799-8573

Call (855) 799-8573. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.

Key Takeaways

  • We diagnose the mechanical gate and the automation together, because the fault is rarely where the homeowner expects it.
  • Free estimates, written and agreed before any work starts.
  • Residential and commercial systems, manual and automated.
  • Multi-brand fluency across nine gate automation brands.

Driveway Gate Repair

Driveway Gate Repair covers the gate at the vehicle entrance – the swing or slide panel, its hinges or carriage, and the operator that moves it. You need it when a panel sags, scrapes, or stops halfway. Most driveway gates in Antioch sit on post-mounted hardware that takes hundreds of cycles a month, and hinge plates wear before the hinge pin does. Inspecting the panel’s movement under load tells us what’s actually failing. Repairs typically run $150-$450 depending on hardware, and we confirm the exact scope in a written estimate before any work starts.

Hinge and Post Hardware

Sagging panels usually trace to loose hinge plates or a post that has shifted in its footing. We re-seat the hardware and check panel alignment rather than simply tightening bolts that will loosen again.

Panel Alignment and Clearance

A gate that binds halfway through its swing is dragging on the ground or the post. We check plumb and level, adjust hinges and reset stops so the panel travels clean while the operator does less work.

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Gate Welding

Gate Welding restores broken joints, cracked frames, and failed hinge mounts that hold the panel together. You need it when a weld has let go at a corner, a grub screw has snapped off, or a post bracket has torqued under the operator’s push. We weld on site where safe and practical, then re-check panel alignment after the heat has cooled so the frame isn’t welded true to a sagging gate. Welding repairs generally run $120-$400 depending on joint count and access. On site, our technicians assess whether a weld repair will hold or whether the frame is fatigued enough that patching only delays a replacement.

Structural Weld Repairs

Corner joints, frame seams and diagonal bracing take the load. We clean back coating, weld, then protect the repair so it lasts in the local sun and dry-season dust.

Hinge and Bracket Welding

Hinge brackets see constant load and often crack at the weld toe. We re-weld the bracket and check the panel’s swing so the hardware doesn’t fail again in the same way.

Commercial Gate Repair

Commercial Gate Repair covers vehicle and pedestrian gates on properties where downtime has an operational cost – storage yards, apartment complexes, HOAs, offices, and light industrial sites. You need it when a gate cycles constantly through the working day, and either stops responding or fails safe in the wrong position. Commercial systems in Antioch usually involve loop detectors, access control and safety edges, so the fault could sit in the mechanical gate, the operator board or the sensor loop. We assess all three before recommending a repair. Most commercial repair calls run $200-$650 depending on control-system work required, with the written estimate setting the final price.

Questions about your gate repair?Free estimate, price agreed before work starts
Call (855) 799-8573

High-Cycle Operator Failures

Operators on heavy commercial gates wear through gearboxes and limit switches faster than residential units. We check cycle counts against what the gate actually runs and flag parts already approaching the end of their service life.

Access Control and Detection

Loop detectors, card readers, keypads and safety edges fail independently of the operator. We test each control point so the repair addresses the sensor that stopped the gate, not the motor behind it.

Iron Gate Repair

Iron Gate Repair handles gates built from iron stock – decorative residential panels, estate entries, and older ornate gates that need a specialist looking at the metalwork and the mechanism together. You need it when cast joints crack, panels rust through, or hardware mounted into iron starts to loosen. Iron gates behave differently from lighter steel: panels are heavier, the operator works harder, and weld repairs need the right filler so the panel doesn’t crack again. Repairs typically run $150-$450 depending on the extent of the weld and hinge work. On a heavier iron panel, we also check the operator’s push force, because a tired operator on a heavy gate is often the real source of the problem.

Rust Treatment and Preparation

Surface rust spreads under the coating long before it shows through as a hole. We strip the affected area back to sound metal before welding so a patch doesn’t fail in a year.

Heavy Panel and Hinge Assessment

Iron panels are heavy enough that the hinge hardware wears faster than on steel. We check pin wear, tighten tolerances and confirm the panel is running on the hardware, not dragging.

Sliding Gate Repair

Sliding Gate Repair deals with gates that travel along a track or cantilever rail – usually the source of erratic stopping, scraping along the ground, or the panel leaving the track entirely. You need it when the gate moves unevenly, grabs, or comes off the guides. Those symptoms are dangerous: a sliding panel that leaves its track can fall across the driveway. We inspect the carriage wheels, guide rollers, track surface and stops before touching the operator, since a track fault often gets misdiagnosed as a motor fault. Sliding gate repairs typically run $180-$550 depending on whether track, rollers, carriage or operator work is involved. The written estimate sets the final price.

Track and Roller Service

Wheel and guide-roller wear is the most common cause of a sliding gate that grabs or drifts. We check bearing play, replace worn rollers, and confirm the track itself is flat and clear.

Panel Derailment and Alignment

A panel that has jumped its guides needs the carriage checked, not just the panel pushed back on. We measure alignment across the full opening before returning the gate to service.

Wrought Iron Gate Repair

Wrought Iron Gate Repair covers decorative wrought iron panels and pickets where the failures involve ornament as much as structure. You need it when a picket is bent or missing, a scroll has cracked, or the hardware driving the operator has worked loose from the decorative leaf. Wrought iron panels are usually lighter than solid iron gates but fragile at the joints, so weld repairs need care not to distort the ornament. Repairs typically run $150-$400 depending on the number of picket and scroll repairs and whether any hinge work is involved. On a wrought iron gate that swings under an operator, we also check that the operator’s force is set correctly for a panel this light.

Want to talk it through?Free estimate, price agreed before work starts
Call (855) 799-8573

Picket and Scroll Repairs

Bent or broken pickets and cracked scrolls are repaired one joint at a time. We match the profile so a repair reads as part of the same panel rather than a patch.

Operator Mounting on Decorative Panels

Operators on wrought iron gates mount to brackets welded to the decorative frame. We check the mounting points and reinforce them where the panel’s light frame is taking the operator’s push.

Metal Gate Repair

Metal Gate Repair covers steel and aluminum gates of every style – tube-frame driveway gates, ornamental aluminum, box-section commercial gate systems. You need it when a metal panel dents, twists, or loses structural shape after an impact, or hardware mounted to the frame starts to tear away. Aluminum frames in particular need different weld technique from steel, and a repair that ignores that difference will fail at the same joint. Repairs typically run $130-$500 depending on the metal, the damage and the operator work involved. We assess the specific metal before quoting so the estimate matches the technique the repair actually needs.

Frame Straightening

Twisted frames come back to shape on the bench before any panel is re-mounted. We measure diagonals and clearances against the opening, not just the frame’s own geometry.

Impact Damage Repair

Most metal gate failures trace to a single impact – the gate driven into, or driven through. We check for hidden cracks at weld toes and confirm the operator’s force settings after the panel has been repaired.

Wood Gate Repair

Wood Gate Repair covers timber gates – driveway swing gates, garden entrances and decorative side gates – where boards, stiles, or hinge mounts fail from weather and repeated cycling. You need it when a board has split, a hinge plate has pulled from the stile, or the gate has started sagging away from square. Wood behaves differently from metal: a repair that replicates the original joint often pulls out again in the same place. We reinforce at the hinge side and cross-brace where the frame is weak, then check swing and speed settings so the operator doesn’t stress the timber more than it should. Repairs typically run $120-$350 depending on board replacement and hinge-side work.

Board and Frame Replacement

Split boards and loose stiles are replaced or sistered with matched timber. We bring the panel back to square before it goes back on the hinges.

Hinge and Gate Hardware

Hinge plates pulling from a stile are a common wood gate failure. We re-secure them with reinforced mounting so the hinge, not the timber, takes the swing load.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
Need a price for your gate repair?Free estimate, price agreed before work starts
Call (855) 799-8573

Brands We Service

We work on the brand you already have, and we know the failure patterns that each one runs into. LiftMaster operators are common on residential driveway gates, and their control boards and limit switches are the parts we most often find behind an intermittent stop. FAAC and BFT systems turn up on heavier and commercial gates, and their terminal blocks and encoder wiring need careful checking when a gate runs to one limit but reverses. Mighty Mule is another brand we see regularly, and we know its battery and solar-charging quirks as well as its mechanical limits. Every brand has components that fail first; we diagnose the specific failure rather than swapping whole units on a hunch.

Whether you have a LiftMaster, a FAAC, a BFT, a Mighty Mule or any other make, we can help. Call us with the brand and model if you have it. If not, tell us what the gate is doing and we’ll take it from there – this applies whether you need gate repair on an existing system or a fresh install quoted.

Signs You Need a Pro Right Now

  • The gate stops midway and reverses. This is often a safety sensor or limit-switch issue, not a motor failure. Leaving it unaddressed can lead to the gate closing on a vehicle or a person.
  • Hinges are loose or the panel sags. A sagging panel forces the operator to push against drag, which burns out motors and trips the controller. Fixing the hinge now is far cheaper than replacing the operator later.
  • The operator motor runs but the gate doesn’t move. That’s usually a stripped gear, a broken arm or a failed clutch. It needs a trained technician on site, because the panel can be weighted with no lock holding it.
  • A sliding panel has left its track. A panel off its rollers can fall across the driveway. Stop using the gate and call us. The danger isn’t the mechanism itself so much as heavy panels moving uncontrolled.
  • The operator doesn’t respond to remotes or keypad. That’s a control or wiring fault, not a mechanical one. It needs a proper diagnostic on the board, and it may trace all the way back to the power feed.

Our Process, Step by Step

  1. 1
    Call and describe the fault. Tell us what the gate is doing, and the brand and model if you know them. We’ll dispatch a technician on a fast dispatch from 7am to 7pm, Sunday through Friday, and if a same-day slot is open we’ll book it.
  2. 2
    On-site assessment. We check the mechanical gate first – hinges, carriage, track, panel alignment – then test the operator, control board, sensors and safety edges. Operators, wiring and control boards carry live voltage, so diagnosis is a job for a trained technician rather than a homeowner with a multimeter.
  3. 3
    Written diagnosis and quote. We explain what’s failing, what options exist, and what each will cost. Nothing is ordered or replaced before you’ve agreed the written estimate.
  4. 4
    Repair on site. Welding, hinge work, operator service and control-board repair happen on site where practical, using parts matched to the brand. If a part needs ordering, we give you the timing up front.
  5. 5
    Test and sign-off. We cycle the gate through a full open/close, check the safety edges and stops, and confirm the panel runs clean before we leave.
Questions about your gate repair?Free estimate, price agreed before work starts
Call (855) 799-8573

How Much Does Gate Repair Cost in Antioch?

Gate repair in Antioch typically runs $120-$650 depending on the type of gate and how deep the fault sits. A simple hinge or weld repair on a manual gate usually lands near the low end. Automated gate repairs that involve an operator motor, control board, loop detector or safety edge sit at the higher end.

A typical driveway gate hinge and alignment repair in Antioch runs $150-$450 depending on hardware. A sliding gate truck or roller replacement runs $180-$550. A commercial system repair with control-board work runs $200-$650. Every range is typical, not fixed – the written estimate you receive on site sets the final price.

What affects the price: the gate material (wood and light aluminum need different technique from steel), the brand and operator age, whether parts are common stock or need ordering, and whether access to the mounting hardware is straightforward or tight. We quote before we start, so there’s no surprise on the invoice.

To avoid overpaying, insist on a written diagnosis before any part is ordered, and be wary of a quote that jumps straight to a full operator replacement without testing the mechanical gate first. In our experience, a large share of “failed operators” turn out to be dragging hinges, a misaligned carriage, or a bad sensor.

Our estimates are free. The estimate covers the diagnosis, the identified fault, and the parts and labor to fix it – nothing more.

Call (855) 799-8573 for an exact quote. Estimates are free.

Our Service Area Near Antioch

We repair gates across Antioch and the surrounding East Contra Costa area. Alongside Antioch, we handle gate repair in Brentwood and gate repair in Oakley, and we also cover Clayton, Discovery Bay, Blackhawk, Camino Tassajara, Walnut Creek, Contra Costa Centre and Rio Vista. Dispatch runs 7am to 7pm, Sunday through Friday, and same-day appointments are usually available when you call before the schedule fills.

Serving Antioch, CA – Our Local Coverage Area

We serve Antioch and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.

Frequently Asked Questions About Gate Repair in Antioch

Schedule Your Gate Repair Service in Antioch Today

From broken hinges to failed operators, one call covers it. Call (855) 799-8573 to book a free estimate for gate repair in Antioch. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. No obligation, no pressure; the price is quoted and agreed before any work starts.

Written by the team at Gate Repair Antioch.

Why Antioch Chooses Gate Repair Antioch

We set the standard for gate repair in Antioch.

30-60 Min Response

Fast dispatch across Antioch, 7am-7pm. Same-day service available.

Licensed & Insured

Fully certified technicians who meet all local and state licensing requirements.

Upfront Pricing

No hidden fees, no surprises. You approve the price before any work begins.

Guaranteed Work

Every repair and installation is backed by our workmanship warranty and satisfaction guarantee.

How It Works in Antioch

Getting your gate repair handled is simple and fast.

1

Call or Request a Free Estimate

Tell us about your gate repair needs and we provide an upfront, transparent quote with no obligation and no hidden fees.

2

Licensed Technician Dispatched

A background-checked, certified technician arrives in Antioch - typically within 30-60 minutes.

3

Problem Solved, Guaranteed

We complete the job to your full satisfaction, backed by our warranty and satisfaction guarantee.

What happens when you call

  1. 1
    A real person answersNo phone trees. Talk to a local gate repair pro.
  2. 2
    You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
  3. 3
    A background-checked tech heads outLicensed & insured, typically within 30-60 min.
  4. 4
    You approve before work beginsNothing starts until you say go.

What Antioch Customers Say

Trusted by homeowners across Antioch and surrounding areas.

★★★★★

"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."

Tara Walsh
★★★★★

"Fixed the immediate problem. He was honest that the operator is near end of life and I should budget for a replacement, which I appreciate even if it wasn't what I wanted to hear."

Neil Patel
★★★★★

"Solar panel on our remote gate wasn't keeping the battery up through the winter. He repositioned it, replaced the battery, and explained the math on why the old placement was never going to work."

Adriana Ramirez

Ready for Gate Repair in Antioch?

Call now for a free estimate, or request one below. Licensed, insured, and here with fast help in Antioch.

(855) 799-8573

Request a Free Estimate in Antioch

Tell us about your gate repair needs. We'll respond within the hour.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Local Service Coverage
Call Now - We Answer 24/7