Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Antioch?
Gate parts and welding in Antioch typically run $95 to $275 for a parts-and-welding repair job, with most hinge, latch, and post repairs landing around $150 to $220. A full gate section replacement with new hardware and metalwork usually falls in the $385 to $1,450 range. The written estimate sets the final price every time, and estimates are free.
We’re Gate Repair Antioch, and the work we see most in Antioch is the everyday kind: a sagging hinge on a driveway gate, a cracked weld where the frame meets the post, a latch that no longer lines up. The material matters a lot here. Steel gate frames in Antioch’s dry summers and wet winters shift at the hinges faster than people expect, and a weld that looked fine in April can start pulling by the following spring. That’s usually a $150-ish fix if you catch it early and a $400-plus job if the gate frame has already started to bend.
Gate Parts & Welding Cost Breakdown (2026)
Here’s what the line items look like for the Antioch market this year. These are estimated ranges for the job, not rates by the hour. The written estimate you get on site is what sets your actual price.
| Line Item | Typical Estimate Range | What It Covers |
|---|---|---|
| Hinge replacement (per hinge, welded) | $95 – $185 | Cut out old hinge, weld new hardware, rehang and align gate |
| Latch and striker repair | $85 – $165 | Replace worn latch, realign striker, test closure |
| On-site weld repair (cracked frame, broken joint) | $150 – $275 | Grind, prep, and weld a single repair point, plus finish |
| Multiple weld repairs (3 or more points) | $275 – $495 | Full frame touch-up across several joints and stress points |
| Gate stop, roller, or guide replacement | $110 – $240 | Slide gate hardware, track rollers, guide posts |
| Post repair or reset (steel) | $225 – $450 | Dig out, reset, re-weld, and refill post footing |
| Post repair or reset (masonry or concrete) | $385 – $725 | Anchor bolts, base plate work, masonry patching |
| Wheel and caster replacement (slide gates) | $95 – $210 | New carrier wheels, axle hardware, re-level |
| Frame section replacement | $385 – $1,450 | Cut out damaged tube section, weld in new steel, paint |
| Safety sensor or loop detector wiring (parts + labor) | $185 – $425 | Replace sensor, run new wire, test the operator’s safety circuit |
| Control board replacement (parts + labor) | $265 – $585 | Board swap on LiftMaster, FAAC, BFT, Linear, Viking, DoorKing, or Elite operators |
| Operator motor or gearbox repair | $325 – $875 | Motor, gearbox, or arm rebuild on a failing operator |
Two forces push that table up or down. The first is whether the problem is mechanical or electrical. Welding and hinge work is predictable, since the surface area of the repair is visible. Automation work is less so at first glance: a gate that won’t close can be a $150 safety-sensor fix or a $500 control-board replacement, and the two look identical from the driveway. That’s why we diagnose before we quote, rather than guessing from a phone description.
The second force is the gate itself. A single-swing residential gate with a steel frame is a fairly quick weld job. A double-driveway gate on a commercial track system, with an operator running a loop detector and two safety beams, takes more time and much more checking. The price reflects the actual work, not a template.
What Affects Gate Parts & Welding Pricing in Antioch
Antioch’s local conditions shape the estimate in ways that the same repair in a cooler or wetter market would not. A few of these are worth knowing before you call.
- Baked metal and warped frames. Antioch summers put real heat into steel gate frames, and after a few seasons that expansion can leave hinges slightly out of plumb even when the weld is still intact. A repair on a twisted frame takes longer than one on a square frame.
- Winter rain and footing movement. Antioch’s wet winters soften the ground around gate posts, and a post that was set correctly in dry soil can shift a quarter inch or more over a few winters. If the post has moved, we re-set the footing, which is why post repair costs more than plain welding.
- Gate type: swing, slide, or commercial. A single-swing residential gate is the simplest repair. A slide gate on a track with rollers and guide posts adds hardware and alignment work. A commercial gate on a busy property line takes longer and gets a different check-out.
- Operator brand. We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule equipment. A control board for a Mighty Mule is not the same price as a commercial DoorKing board, and we quote each on what the equipment actually needs.
- Material and finish. Bare steel is straightforward to weld and finish. Powder-coated or painted gates require careful prep and a color-matching touch-up, which adds time to the job.
- Access and working room. A gate you can walk around both sides of is easier to weld than one wedged against a fence line or a building, and the difference shows up in labor.
How to Save on Gate Parts & Welding
The cheapest repair is the one you catch early. A hinge that starts to sag or a latch that’s drifted an eighth of an inch is a small fix. Left alone for another season, that same hinge can pull the frame out of alignment, and now you’re paying for post work and re-welding instead of one hinge.
- Watch the gate’s swing line. If the gate drops, drags, or scrapes the ground, get it checked. Catching that early stays in the $95 to $185 range.
- Clear vegetation and soil from the gate’s arc. Roots and debris in the swing path stress hinges and motors. They also make the site harder to work on.
- Fix the mechanical problem before you touch the automation. A bent gate will burn out an operator’s gearbox within a season. Sorting the physical alignment first protects the electrical equipment.
- Ask for the estimate in writing. We provide free estimates on site, so you know the number before any work begins. Call (855) 799-8573 and we’ll set it up.
- Bundle the small items. If you’re already having one weld done, the second and third weld points cost much less than scheduling separate visits.
For larger patterns in what these jobs cost in the area, our Antioch page has related service and pricing information, and our team can talk through whether the work fits standard pricing or a larger frame repair.
How We Price a Gate Repair in Antioch
We diagnose first, then quote. When we arrive on a gate repair call in Antioch, the technician inspects the gate, the posts, the hardware, and the operator if there is one. That means checking the swing, the level, the weld points, the latch alignment, the operator’s control box, and any safety sensors or loop detectors. From there we write a scope of work and a price, and the price is set per job by that written estimate.
There’s no diagnostic fee. The estimate is free, and that applies whether you’re just getting a hinge fixed or planning a larger frame repair. If we’re already at the property for a mechanical problem and something else shows up, we’ll tell you about it and note it in the estimate. What we won’t do is turn a broken hinge into a full replacement if a repair is the right call. That’s what “diagnose first, then fix” means in practice.
Do You Need Welding, a Part, or a Whole New Gate?
Not every gate problem needs welding, and not every welding quote should be a replacement quote. Here’s how we think about it.
- Weld repair covers a cracked joint, a rusted-through stress point, a broken hinge mount, or a section of frame that has split but left the rest intact. This is the most common repair we do.
- Part replacement covers a hinge, latch, roller, guide, wheel, or safety sensor that has failed mechanically. Swapping the part is cheaper than re-welding a joint that isn’t the problem.
- Post reset covers a gate whose post has tilted or shifted, usually because the footing has moved. Sometimes the weld is fine and the post isn’t, and re-setting the footing is what actually fixes the gate.
- Frame section replacement is for a gate where a substantial piece of the frame is bent or rusted beyond repair. The new section is welded in and finished, and the gate stays on its existing posts.
- Full gate replacement is a separate job altogether. If the frame is warped beyond straightening, the posts are gone, and the gate has been patched multiple times, then a new gate is often the better long-term call. When that’s the case we’ll tell you so and walk you through what a replacement looks like.
What a Gate Repair Visit Actually Involves in Antioch
Antioch residential gates take a beating from the local weather. Dry summers crack the finish on steel and swell wood, and wet winters shift the soil around posts. By the time a gate is dragging or a hinge is squealing, several seasons of expansion and contraction have usually happened. A repair visit addresses the actual damage, not the symptom.
Our technicians have up to 11 years of experience, and most repair visits follow the same pattern. The technician inspects the gate, checks the posts for movement, checks the hinge and latch wear, and looks at the operator’s control system if the gate is electric. We bring welding equipment for on-site welding on steel gates. We test the gate after the repair, and we test the operator’s safety circuit if there is one. If a follow-up visit turns out to be needed, we tell you before we leave.
Gate Parts & Welding Safety for Electric Gates
An electric gate carries real danger. The operator’s low-voltage control wiring is one thing, but the 120-volt supply to the operator, the battery backup, and the control board inside the housing are not a homeowner project. Getting inside a gate operator housing without the right isolation procedure can cause serious shock injury, and a safety sensor that’s been disabled or bypassed is a crush hazard. We don’t recommend opening the operator housing yourself.
The mechanical side has its own hazards too. A swing gate has pinch points at every hinge and gate stop, and a slide gate that has left its track can crush without warning. Heavy gate panels can fall if a hinge or weld gives way while it’s being moved by hand. If a hinge or weld looks cracked, don’t force the gate to test it. Get a technician out to check it. Same goes for the post footing: a leaning post that’s been braced by a homeowner is still a leaning post, and the fix is a proper re-set.
Parts, Welding, and Automation on One Visit
Most gate repair calls in Antioch start with a physical problem and reveal a second issue. The hinge is cracked, and the operator that pushes the gate has been straining against the misalignment for months. Or the gate is fine, but the safety beam keeps triggering. That’s why we cover the full range of gate work on one visit: mechanical repair and welding, electric operator and control-system diagnosis, and new gate installation when that’s the right answer.
We work on the brand you already have. That includes LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule equipment. Our technicians have working knowledge of all nine, which means we can go straight to the right control board, the right sensor, or the right replacement part without guessing. If a part isn’t the answer and a weld is, we say so, and if a weld isn’t the answer and a part is, we say that too.
For a full picture of what our team handles, see our gate repair page or reach out directly. One call covers the diagnosis, the estimate, and the fix, whether the problem is a bent hinge or a failing control board.
FAQs – Gate Parts & Welding Cost
How much does gate welding cost in Antioch?
Gate welding in Antioch typically costs $150 to $275 for a single repair point, and multiple weld repairs typically run $275 to $495. A full frame section replacement is a bigger job in the $385 to $1,450 range. Call (855) 799-8573 for an exact quote, and estimates are free.
Is it cheaper to repair or replace a gate?
Repair is almost always cheaper than replacement when the posts and frame are sound. A hinge or weld repair in the $95 to $275 range costs far less than a full gate replacement. Replacement only makes financial sense when the frame is warped, the posts have failed, and the gate has been patched repeatedly. Call (855) 799-8573 and we’ll give you an honest read on which way to go.
Can you come today?
Same-day service is often available for gate repair in Antioch. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. Call (855) 799-8573 and we’ll book the next available slot.
How much does an electric gate part cost to replace in Antioch?
Electric gate parts are usually the largest line item on the estimate. A safety sensor or loop detector job runs $185 to $425, a control board replacement runs $265 to $585, and an operator motor or gearbox repair runs $325 to $875. Call (855) 799-8573 for an exact quote on your operator’s brand, and estimates are free.
Do you work on the gate brand I already have?
Yes. We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule equipment. That means we can diagnose the operator you already own without sending you to another contractor. Call (855) 799-8573 to talk through what your gate is doing.
Key Takeaways
- Typical gate parts and welding jobs in Antioch run $95 to $275.
- Frame section replacement is a larger job at $385 to $1,450.
- Electric gate parts (control boards, sensors, motors) are the biggest single line item.
- Welding, part replacement, and automation work can all be handled on one visit.
- Estimates are free, and the written estimate sets the final price.
Get a Free Gate Parts & Welding Estimate in Antioch
If your gate is dragging, a hinge is cracking, or an electric operator has started acting up, we can diagnose it and quote the fix. We accept both residential and commercial gate work across Antioch and the surrounding area. Call (855) 799-8573 for a free estimate. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday.
Pricing reflects the Antioch market as of 2026. Gate Repair Antioch offers free estimates – call (855) 799-8573.
Written by the team at Gate Repair Antioch.
What Our Customers Say
"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
- Tara Walsh"Fixed the immediate problem. He was honest that the operator is near end of life and I should budget for a replacement, which I appreciate even if it wasn't what I wanted to hear."
- Neil Patel"Solar panel on our remote gate wasn't keeping the battery up through the winter. He repositioned it, replaced the battery, and explained the math on why the old placement was never going to work."
- Adriana Ramirez